How Many Lumens Do I Need for a Garage or Workshop?

"How bright should my garage lights be?" is really a math question, and the math is simple once you know three numbers: how big the room is, what you do in it, and how much light each fixture puts out. This guide walks through the calculation step by step, with worked examples for a two-car garage used for parking and the same garage set up as a workshop. Then it covers the things that change the answer, like ceiling height and wall color, and how to lay the fixtures out so the light lands where you need it.

The quick answer

Multiply your floor area by a lumens-per-square-foot target, then divide by the lumens listed for the fixture you plan to use. Common rules of thumb are about 50 lumens per square foot for a garage used for parking and storage, and about 75 to 100 lumens per square foot for a workshop where you do detailed work. For a 400 sq ft two-car garage, that's roughly 20,000 lumens for parking and 30,000 to 40,000 lumens as a workshop. Treat these numbers as starting points for planning, not code requirements.

Step 1: Measure the floor area

Measure the length and width of the space in feet and multiply. A garage that is 20 ft by 20 ft is 400 sq ft. If part of the room is a separate work zone, like a bench along the back wall, note its size too. You'll plan extra light for it later.

Step 2: Pick a lumens-per-square-foot target

Choose a target based on how you actually use the space. These are common planning ranges from garage and workshop lighting guides:

  • Parking and storage: about 50 lumens per sq ft. Enough to walk safely, find things on shelves and see around the car.
  • General workshop: about 75 lumens per sq ft. Projects, repairs, sorting tools and parts.
  • Detailed work: about 100 lumens per sq ft or more. Woodworking, mechanical work, painting, small parts. Many people add task lighting over the bench instead of raising the whole room to this level.

If you've seen light levels given in footcandles, it's the same unit: one footcandle equals one lumen per square foot. A light meter (or a phone light-meter app) reads footcandles at the surface you point it at. Expect that reading to be lower than your fixture math, because some light is lost between the fixture and the floor. That's one reason to round up.

Chart of starting-point lumen targets for a garage or workshop: about 50 lumens per square foot for parking and storage, about 75 for a general workshop and about 100 or more for detailed work, shown as three bars on a whiteboard-style panel
Starting-point targets by use. Rules of thumb for planning, not code.

Step 3: Multiply to get your total lumens

Floor area × target = total lumens. For the 400 sq ft garage:

  • Parking and storage: 400 × 50 = 20,000 lumens
  • Workshop: 400 × 75 to 400 × 100 = 30,000 to 40,000 lumens

Step 4: Divide by the fixture's listed lumens

Now divide the total by the lumen output listed for the fixture or tube you're considering, and round up. The listed output for Orilis products, from the product pages:

  • 4 ft LED vapor tight fixture: 72W, 8,000 lumens
  • 2 ft LED vapor tight fixture: 36W, 3,600 lumens
  • 4 ft double-ended LED T8 tube: 22W, 3,000 lumens per tube (so a 2-tube shop light converted to LED gives about 6,000 lumens)

Worked example A: a 400 sq ft garage for parking

  • Target: 20,000 lumens
  • With 4 ft vapor tights: 20,000 ÷ 8,000 = 2.5, round up to 3 fixtures (24,000 lumens listed)
  • Converting 2-tube shop lights to LED tubes: 20,000 ÷ 6,000 = 3.3, round up to 4 fixtures (8 tubes, 24,000 lumens listed)

Worked example B: the same garage as a workshop

  • Target: 30,000 to 40,000 lumens
  • With 4 ft vapor tights: 30,000 ÷ 8,000 = 3.75 and 40,000 ÷ 8,000 = 5, so 4 to 5 fixtures
  • Converting 2-tube shop lights: 30,000 ÷ 6,000 = 5 and 40,000 ÷ 6,000 = 6.7, so 5 to 7 fixtures (10 to 14 tubes)

Rounding up matters more than it seems. The fixture count also has to fit a sensible layout (Step 6), so it's normal to land one fixture above the bare math.

Worked example on a whiteboard: 20 ft by 20 ft equals 400 square feet; times 50 lumens per square foot equals 20,000 lumens for parking; divided by 8,000 lumens per 4 ft vapor tight equals 2.5, rounded up to 3 fixtures; workshop at 75 to 100 lumens per square foot equals 30,000 to 40,000 lumens, or 4 to 5 fixtures
The whole calculation for a 400 sq ft garage: area × target ÷ listed lumens, then round up.

Step 5: Adjust for ceiling height and wall color

The per-square-foot targets assume a fairly typical room. Move toward the high end of the range, or add a fixture, when:

  • The ceiling is high or open. The farther the light has to travel to the floor or bench, the less of it arrives there. Tall ceilings and open rafters also give the light more places to go.
  • The walls, ceiling or floor are dark. White and light-gray surfaces bounce light back into the room. Dark paint, bare wood, black mats and stained concrete absorb it.
  • The room is full. Tall shelves, cabinets, a parked truck or a big machine cast shadows that another fixture or a task light can fill.

The opposite is also true: a garage with white walls and a white ceiling often looks brighter than its numbers suggest. Painting the walls a light color is one of the cheapest lighting upgrades you can make.

Garage with dark charcoal walls and open rafters, with a whiteboard note: high ceiling or dark walls, aim for the high end of the range or add a fixture; light-colored walls bounce light back into the room
High ceilings and dark surfaces swallow light. Plan toward the top of your range.

Step 6: Lay out the fixtures for even light

Several fixtures spread evenly beat one very bright light in the middle of the ceiling. One central light leaves dark corners and throws hard shadows over the bench and around the car. A common layout rule from woodworking-shop guides:

  • Measure from your work surface (a bench is often around 3 ft high) up to the fixtures. Call that distance A.
  • Keep rows of fixtures no more than about 1.5 × A apart.
  • Keep the outer rows about one-third to one-half of that row spacing from the walls, so the edges of the room don't go dark.
  • Run 4 ft fixtures lengthwise, from the garage door toward the back wall.

In a 20 × 20 ft garage with a 10 ft ceiling, A is about 7 ft, so rows can be up to roughly 10 ft apart. Three rows work well: one down the middle, between the two parking spots, and one about 3 to 4 ft in from each side wall, between the car and the wall. For parking, one 4 ft vapor tight per row (3 fixtures) meets Example A. For a workshop, put two fixtures in each outer row and one or two in the middle row to reach Example B. Keep fixtures clear of the garage door track and the opener. Our one-weekend garage LED upgrade plan covers the install side of a garage project.

Top-down floor plan of a 20 by 20 foot two-car garage with three rows of 4 ft fixtures running front to back: one row between the two parking spots and one row about 3 to 4 feet in from each side wall, with soft light zones overlapping across the floor and a separate task light over the workbench on the back wall
Three rows in a two-car garage: one between the spots, one near each wall, plus a light over the bench.

Step 7: Add task lighting over the workbench

Instead of oversizing the whole room, put extra light where the detailed work happens. Mount a fixture above the front edge of the bench, not behind you. With the only light at your back, your head and shoulders shade the work. A 2 ft vapor tight (3,600 lumens listed) fits over a short bench, and a 4 ft fixture covers a longer one. If the bench sits against a wall, the fixture over its front edge also lights the pegboard behind it.

Garage workbench with a vise and tools, lit by a linear LED fixture mounted over the front edge of the bench, with a marker arrow showing that light from the front avoids casting your own shadow on the work
Task light over the front edge of the bench keeps your own shadow off the work.

Which Orilis lights fit the plan?

Before and after: why the layout matters as much as the lumens

Two garages can have the same total lumens and look completely different. One bright fixture in the center leaves the corners, the shelves and the bench in shadow. The same output split across several evenly spaced fixtures fills the room, so you can see the floor around the car and the work in front of you.

Side-by-side comparison: on the left, a dark two-car garage lit by a single bare bulb with deep shadows in the corners; on the right, a garage evenly lit by several linear LED fixtures with no dark corners
Same goal, different result: one central light vs. several fixtures spread across the ceiling.

Quick checklist

  1. Measure length × width for the square footage.
  2. Choose a starting target: about 50 lm/sq ft for parking, about 75 to 100 for a workshop.
  3. Multiply for total lumens.
  4. Divide by the fixture's listed lumens and round up.
  5. Go toward the high end for high ceilings, dark surfaces or a crowded room.
  6. Lay out rows evenly, with outer rows close enough to the walls.
  7. Add a task light over the front edge of the bench.
  8. Use one color temperature throughout.

Safety first: converting a fixture or hardwiring a new one is line-voltage work. Turn the power off at the breaker and confirm it's off with a voltage tester before you open any fixture or ceiling box. If you're not sure, hire a licensed electrician. See do I need an electrician to install an LED retrofit kit?

Orilis tip: Add extra light over the workbench rather than oversizing the whole room. It puts the brightness where your eyes need it.

Ready to light up your garage or workshop?

Shop double-ended LED tubes, the 4-light retrofit kit or vapor tight fixtures at orilis.com. Questions about your layout? Email info@orilis.com or call 1-407-900-9745.

Leave a comment

Please note, comments must be approved before they are published