LED Troffer Lighting: What's in Your Ceiling and How to Upgrade It

Look up in almost any office, school, clinic or store and you'll see them: flat rectangles set into the ceiling grid, each holding a few fluorescent tubes. Those are troffers, and there's a good chance yours are due for LED. Here's how to tell what you have and the simplest way to upgrade it.

What a troffer is

The name blends "trough" and "coffer." A troffer is a rectangular fixture made to drop into a suspended (T-bar) tile ceiling, usually 2x4 ft, 2x2 ft or 1x4 ft. The U.S. Department of Energy counts more than 350 million troffers in U.S. commercial buildings, and most were built around fluorescent tubes.

Identify yours in a minute

  • Size: count the ceiling tiles it replaces. One 2x4 tile is the most common.
  • Tubes: how many, and how long? 2x4 and 1x4 troffers usually hold 4 ft T8 (or older T12) tubes. 2x2 troffers usually take shorter or U-bend tubes.
  • Face: a flat prismatic lens, a grid of shiny parabolic louvers, a perforated "basket" (recessed indirect) or a curved volumetric lens.
  • Condition: rust, cracked or yellowed lenses, peeling paint or a humming ballast.

Three ways to upgrade

DOE describes three paths for fluorescent troffers: swap the lamps for LED tubes, install an LED retrofit kit inside the existing housing, or replace the whole fixture with a new LED troffer. Retrofitting or replacing can cut energy use by roughly 20% to 60% at the project level, according to DOE.

Orilis doesn't sell troffers. What we do sell fits the first two paths for any troffer that takes 4 ft T8-size tubes:

  • Double-ended LED T8 tubes: 22W, about 3,000 lumens each (a standard 4 ft fluorescent T8 is rated 32W, plus the ballast), frosted, 85-277V, in 4500K, 5000K or 6500K. These are ballast bypass tubes: the ballast comes out, so there's no ballast left to fail.
  • The 4-light retrofit kit: four 22W double-ended tubes, eight non-shunted lamp holders, six loop wires, two sets of 48" connecting wires (Line and Neutral) and four wire nuts. That's enough for one 4-lamp troffer or two 2-lamp troffers.

Orilis tubes are 4 ft only, so for 2x2 troffers you'd need a different product.

Retrofit or replace?

  • Housing solid, lens clean? Convert it. You keep the ceiling intact and skip above-ceiling work.
  • Ballast more than 5 years old? DOE advises against tubes that rely on it. Bypass tubes take the ballast out of the picture.
  • Parabolic louvers? DOE notes LED tubes can show more glare in some louvered troffers. Look at one converted fixture before you do the whole floor.
  • Rusted, cracked or badly yellowed? Replace the fixture. In back rooms, garages or damp spaces with no tile ceiling, Orilis vapor tight LED fixtures (surface-mounted, IP65) come in 2 ft and 4 ft, in 4500K or 6500K.

Ask your utility about lighting rebates before you buy. Programs vary, and some pay differently for kits and new fixtures.

More reading: LED office lighting, room by room, integrated LED vs LED tube fixtures, ballast bypass vs plug-and-play and how to convert a 4 ft fluorescent fixture.

Safety first: turn the power off at the breaker and confirm it with a voltage tester before opening any troffer. Wire Line to one end and Neutral to the other through non-shunted sockets, and label each converted fixture. Older buildings can have asbestos in or above the ceiling tiles, so don't disturb tiles you're unsure about. If you're not comfortable with line-voltage work, hire a qualified, licensed electrician.

Ready to upgrade your ceiling?

Shop double-ended LED tubes, the 4-light retrofit kit or vapor tight fixtures at orilis.com, email info@orilis.com or call 1-407-900-9745.

Leave a comment

Please note, comments must be approved before they are published